Quick Add
1-Way UHF High Gain Masthead Amplifier
Product Code: PROMHD11H
- High gain masthead amplifier
- F-Type connections
- 1 input 1 output
- Suitable for outdoor use
Payment methods accepted
Product Description
High Gain (27dB) UHF Masthead Amplifier for 1 TV
Do you have problems with poor TV signal, and wondered how to boost reception?
Our high performance, masthead amplifiers are ideal for boosting your UHF TV signal. They are extremely low-noise (reduced interference) offering better signal quality.
How do I install my UHF amplifier?
Masthead amplifiers are installed externally in a robust weather-proof casing, which slides up to reveal the amplifier. This is typically installed on the aerial pole.
It also requires a power supply which can be bought separately or as a kit. The power supply is installed behind one of the TVs in the system. Simply install the power supply inline with the cable and plug it in to a mains socket. It then sends power up the cable to the masthead amplifier. This is ideal if you cannot install a distribution amplifier in the loft due to lack of a mains socket. Please note: any 5-12V source can be used instead of a power supply.
Features:
- Fully-screened masthead amplifiers with 'F' connector (screw on) outputs. Which means less interference caused by passing vehicles or other strong signals the F connectors ensure the lowest loss on a weak signal and screw on for a secure connection.
- Low noise figures and well-filtered inputs. Low noise figures help because on a weak signal you already have lots of noise and the last thing you want an amplifier to do is add more noise to it.
- Sharp cut off below 400MHz, helps avoid interference problems from nearby transmitters: CB, PMR, TETRA, HF and VHF amateur radio, etc.
- Variable gain models have inter-stage control to maintain good noise figure at reduced gain. Variable gain means you can adjust the amount of amplification required to either boost your signal.
- With equipotential bonding point. This is to allow you to earth the amplifier and help discharge static electricity.
Technical Information:
Product Code | Ways | *Gain | *Noise Figure | *Max Input | *Power Requirement | Typical Applications |
PROMHD11L | 1 | 9dB | 1.8dB | 80dBV | 5 - 12V, 25 mA | Margin raising preamplifier |
PROMHD11M | 1 | 16dB | 1.7dB | 75dBV | 5 - 12V, 25 mA | For weaker signal areas |
PROMHD11H | 1 | 27dB | 1.8dB | 74dBV | 12V, 50 mA | Long downleads, splitters |
*Gain: This is the amount of amplification the amplifier can provide and the higher the number the more it will boost your signal.
*Noise figure: Low noise figures help because on a weak signal you already have lots of noise and the last thing you want an amplifier to do is add more noise to it.
*Max Input: The maximum amount of signal the amplifier can safely handle on the input from the transmitter/aerial.
*Power requirement: The power supply’s required voltage and ampage to drive the amplifier.
The maximum output level per multiplex is per the table in dBV when there are eight equal level multiplexes. If the number of multiplexes to be carried is not eight please refer to our Mux guide.
Related products
Alternative products
Product Description
High Gain (27dB) UHF Masthead Amplifier for 1 TV
Do you have problems with poor TV signal, and wondered how to boost reception?
Our high performance, masthead amplifiers are ideal for boosting your UHF TV signal. They are extremely low-noise (reduced interference) offering better signal quality.
How do I install my UHF amplifier?
Masthead amplifiers are installed externally in a robust weather-proof casing, which slides up to reveal the amplifier. This is typically installed on the aerial pole.
It also requires a power supply which can be bought separately or as a kit. The power supply is installed behind one of the TVs in the system. Simply install the power supply inline with the cable and plug it in to a mains socket. It then sends power up the cable to the masthead amplifier. This is ideal if you cannot install a distribution amplifier in the loft due to lack of a mains socket. Please note: any 5-12V source can be used instead of a power supply.
Features:
- Fully-screened masthead amplifiers with 'F' connector (screw on) outputs. Which means less interference caused by passing vehicles or other strong signals the F connectors ensure the lowest loss on a weak signal and screw on for a secure connection.
- Low noise figures and well-filtered inputs. Low noise figures help because on a weak signal you already have lots of noise and the last thing you want an amplifier to do is add more noise to it.
- Sharp cut off below 400MHz, helps avoid interference problems from nearby transmitters: CB, PMR, TETRA, HF and VHF amateur radio, etc.
- Variable gain models have inter-stage control to maintain good noise figure at reduced gain. Variable gain means you can adjust the amount of amplification required to either boost your signal.
- With equipotential bonding point. This is to allow you to earth the amplifier and help discharge static electricity.
Technical Information:
Product Code | Ways | *Gain | *Noise Figure | *Max Input | *Power Requirement | Typical Applications |
PROMHD11L | 1 | 9dB | 1.8dB | 80dBV | 5 - 12V, 25 mA | Margin raising preamplifier |
PROMHD11M | 1 | 16dB | 1.7dB | 75dBV | 5 - 12V, 25 mA | For weaker signal areas |
PROMHD11H | 1 | 27dB | 1.8dB | 74dBV | 12V, 50 mA | Long downleads, splitters |
*Gain: This is the amount of amplification the amplifier can provide and the higher the number the more it will boost your signal.
*Noise figure: Low noise figures help because on a weak signal you already have lots of noise and the last thing you want an amplifier to do is add more noise to it.
*Max Input: The maximum amount of signal the amplifier can safely handle on the input from the transmitter/aerial.
*Power requirement: The power supply’s required voltage and ampage to drive the amplifier.
The maximum output level per multiplex is per the table in dBV when there are eight equal level multiplexes. If the number of multiplexes to be carried is not eight please refer to our Mux guide.
Technical Specification
IEC or F Type
F Type
Number of Outputs
1
Number of Inputs
1
Low, Medium or High
High (27dB)
Internal or External
External
Amplifier Includes Power Supply Unit (PSU)
No
Amplifier Includes Full Output
No
Product Requires Power Supply Unit (PSU)
No
RED Class 0 or Class 1
Class 0
Width
45mm
Depth
90mm
Height
105mm
Weight
0.19Kg
15/04/2024
13/04/2024
Ok until Blake sold me an item they didn't have in stock ...
05/04/2024
Very good service as a company, very let down by sending out parts poorly packaged, must cost a fortune sending replacements out..
05/04/2024
Seem fine
05/04/2024
First pole arrived with dents in, no packaging just labels. Second arrived still with a small dent, better packing required..
Google Company Reviews
13/04/2024
Thanks for your quick response 👍🏾 And fair pricing for that Camera Arrived next day in time for me to install it... Kind regards Roy
01/04/2024
Excellent service, speedy delivery
30/03/2024
Very happy with my new tv aerials and solved a lot of interference issues out many thanks
23/03/2024
Good, well made coaxial TV antenna and F-Type satellite socket wall plate. It works well. The packaging could have done with some bubble wrap around the socket though for protection.
22/03/2024
Super quick service. Please use less tape on the mast next time :-)
Payment methods accepted
Product Description
High Gain (27dB) UHF Masthead Amplifier for 1 TV
Do you have problems with poor TV signal, and wondered how to boost reception?
Our high performance, masthead amplifiers are ideal for boosting your UHF TV signal. They are extremely low-noise (reduced interference) offering better signal quality.
How do I install my UHF amplifier?
Masthead amplifiers are installed externally in a robust weather-proof casing, which slides up to reveal the amplifier. This is typically installed on the aerial pole.
It also requires a power supply which can be bought separately or as a kit. The power supply is installed behind one of the TVs in the system. Simply install the power supply inline with the cable and plug it in to a mains socket. It then sends power up the cable to the masthead amplifier. This is ideal if you cannot install a distribution amplifier in the loft due to lack of a mains socket. Please note: any 5-12V source can be used instead of a power supply.
Features:
- Fully-screened masthead amplifiers with 'F' connector (screw on) outputs. Which means less interference caused by passing vehicles or other strong signals the F connectors ensure the lowest loss on a weak signal and screw on for a secure connection.
- Low noise figures and well-filtered inputs. Low noise figures help because on a weak signal you already have lots of noise and the last thing you want an amplifier to do is add more noise to it.
- Sharp cut off below 400MHz, helps avoid interference problems from nearby transmitters: CB, PMR, TETRA, HF and VHF amateur radio, etc.
- Variable gain models have inter-stage control to maintain good noise figure at reduced gain. Variable gain means you can adjust the amount of amplification required to either boost your signal.
- With equipotential bonding point. This is to allow you to earth the amplifier and help discharge static electricity.
Technical Information:
Product Code | Ways | *Gain | *Noise Figure | *Max Input | *Power Requirement | Typical Applications |
PROMHD11L | 1 | 9dB | 1.8dB | 80dBV | 5 - 12V, 25 mA | Margin raising preamplifier |
PROMHD11M | 1 | 16dB | 1.7dB | 75dBV | 5 - 12V, 25 mA | For weaker signal areas |
PROMHD11H | 1 | 27dB | 1.8dB | 74dBV | 12V, 50 mA | Long downleads, splitters |
*Gain: This is the amount of amplification the amplifier can provide and the higher the number the more it will boost your signal.
*Noise figure: Low noise figures help because on a weak signal you already have lots of noise and the last thing you want an amplifier to do is add more noise to it.
*Max Input: The maximum amount of signal the amplifier can safely handle on the input from the transmitter/aerial.
*Power requirement: The power supply’s required voltage and ampage to drive the amplifier.
The maximum output level per multiplex is per the table in dBV when there are eight equal level multiplexes. If the number of multiplexes to be carried is not eight please refer to our Mux guide.
Related products
Alternative products
I researched for many TV aerials and my friend who was ex aerial rigger recommended me Blake aerials as you can’t go wrong with them that was his words and it was true